511 Spray On Grout Sealer15 Oz. - $17.99


511 Spray On Grout Sealer - 15 Oz.

Water & Stain Protection for New and old grout
Will not Harm Ceramic Tile, Porcelain Tile, Glazed Tile, Quarry Tile, Glass or Plastic Tile, Marble, Granite, Limestone, Travertine, Slate, other Natural Stone
In stock - Ship Same Day
Miracle 511 Spray-On Grout Sealer is a new fast & easy way to seal tile grout. This unique spray-on sealer provides an invisible barrier that is resistant to oil, stains and water absorption
• Penetrates & Seals Grout • Stain & Water Resistant • 20-Year Warranty • Interior & Exterior Uses
• Easy To Use "Clean Hands" Approach • Directional Spray
• Apply as little as 2 hours after Grouting • Weather Resistant
• Low Toxicity • Non Coating • Non Yellowing
• U.V. Transparent • Economical • Tamper Proof Container
• Contains NO CFCs • Recyclable (doesn’t end up in a landfill)
• Hermetically Sealed against Bacteria Contamination
This product is formulated for sealing all types of new and old grout to provide resistance against water, oils, alkalis, acids, and staining. 511 Spray-On Grout Sealer is a unique formulation designed for the protection of all types of grout both new and old.
511 Spray-On Grout Sealer penetrates into the surface and forms an invisible barrier that is resistant to moisture and stains, while allowing vapor to escape. 511 Spray-On Grout Sealer is not a surface coating and will not alter the natural look while making the grout easier to clean. 511 Spray-On Grout Sealer can be applied to freshly installed grout as quickly as 2 hours after grouting. 511 Spray-On Grout Sealer can be used on interior and exterior applications. 511 Spray-On Grout Sealer is U.V. transparent and will not yellow under any circumstances. 511 Spray-On Grout Sealer averages five to twenty times the coverage of competitive products. (See coverage chart). 511 Spray-On Grout Sealer uses a "Clean Hands" approach to grout sealer application and has a unique directional spray allowing the user to apply the sealer without touching their hands.

New Installation - Application Instructions
Read entire label and PDS/MSDS before using. 511 Spray-On Grout Sealer should not be diluted or thinned in any way. 511 Spray-On Grout Sealer should be used as is direct from approved container.
After Grouting: Once grouted, make sure that all grout residue is removed from the surface with a clean sponge and water. Allow grout to cure per manufacturers specification or at least 2 hours. If grout clean up is not performed effectively, an additional cleaning may be necessary to remove remaining grout residue or haze. For this procedure use Phosphoric Acid Cleaner, (GCFR) Grout & Concrete Film Remover (Hydrochloric Acid), Sulfamic Acid Crystals or Epoxy Grout Film Remover following the instructions carefully. Once the cleaned area has completely dried, proceed with the sealing of the grout for water and stain resistance.
Apply 511 Spray-On Grout Sealer to all grout with the unique "Clean Hands" Spray. Any excess sealer that gets on the surface should be wiped off with a clean towel before it dries.
Existing Installation - Surface Preparation
Surface must be dry and free of contaminants, including previously applied sealers, dirt, lime & hard water deposits, efflorescence, rust & other heavy dirt and grime.
Surface Coating/Wax Removal: To remove existing coatings and/or waxes, use Mira Strip or H2O Strip as directed.
Heavy Duty Cleaning: To remove lime and hard water deposits, efflorescence, rust, grease and other heavy dirt and grime use GCFR (Grout & Concrete Film Remover) or Phosphoric Acid Cleaner as directed.
For a non-acid deep clean use Liquid Poultice as directed.
Light Cleaning: Use Mira Clean #1, Porcelain & Ceramic Tile Cleaner, Mira Soap or Counter Kleen as directed.
Existing Installation - Application Instructions
Once all grout and surrounding surfaces are clean, proceed with the application instructions previously mentioned.
Always Sample Testing
Due to the differences of each substrate, several inconspicuous test patches should be completed to assure maximum performance. User must determine the suitability of the product for their intended use.
Water, Stain & Slip Protection
To protect cleaned areas from future soiling, staining and increase static coefficient of friction, we recommend applying the appropriate Miracle Penetrating Sealer/Impregnator.
Mold, Mildew and Bacteria Sanitation
For best results in killing mold, mildew, bacteria and other microorganisms, use Miracle Wipes as directed.
Color Enhancement For added color with "TEXTURED AND NON POLISHED" surfaces, 511 Seal & Enhance may be applied as directed.
Gloss Enhancement For a higher gloss finish on POLISHED stone surfaces, use Water Ring & Etch Remover, Marble Conditioner, Mira Dust, Mira Polish or Granite Brite. For counters and furniture, use Stone Polish. For tile surfaces, try Tile Brite.
Read entire label and PDS/MSDS before using.
Cure Time 511 Spray-On Grout Sealer will be dry to the touch in 1 - 3 hours and may be used for normal foot traffic. For optimum results the area should be kept dry and free from staining materials for 72 hours.
Coverage: Coverage: Up to 250 Linear Feet per Can.

More Sealers and Care Product Available on our web site

Our store open to the public
5047 W Jefferson Blvd Los Angeles CA 90016
Mon - Fri 7:00 am - 5:00pm
Sunday 12 noon - 4:00pm
For more product visit our web site http://www.flooringsupplyshop.com/
Or call us at 323-731-8453